Maintenance

Replaced some of fuel and ignition parts:

1. WALKER PRODUCTS 25024002 (250-24002) Oxygen (O2) Sensor 

 

2. MOPAR 68405575AA Throttle Position Sensor (TPS)

3. Genuine OEM Bosch Fuel Injectors Set (6) 0280155703

Fuel Injector Specs:    Bosch fuel injector, EV1 style connector, 4 hole nozzle
Flow Rate at 43.5 psi / 3 bar:    23 lb/hr, 241.3 cc/min
Resistance:    12 ohms
1% with dynamic flow results 

Ordered from https://www.cspinjectors.com/product-page/genuine-oem-bosch-fuel-injectors-set-6-0280155703-rebuilt-lifetime-warranty

 

old injectors

Done

4. Taylor Cable 84649 - Taylor ThunderVolt 8.2mm Spark Plug Wire Sets

5. Throttle body butterfly plate is centered and gap adjusted a paper thin as googled

Idles much better and smoke smells normal.

Wireless phone charger

Ordered Baseus Smart Wireless Charging Suction Cup Mount and removed suction cup. made a adapter to mount charger to the side of center console.

 

 

 

New Battery

 Replaced 5 year old battery with new one. 

Solite 105D31R

12V, 90AH, 750CCA

Spare parts

Spare parts arrived,

SKF STCK242 Transfer Case Overhaul Kit

 

 

TRANSFER CASE CHAIN BORG-WARNER HV-028 1" WIDE 36 LINKS

 

WALKER PRODUCTS 25024002 (250-24002) Oxygen (O2) Sensor and MOPAR 68405575AA Throttle Position Sensor (TPS)

New tires and wheels

Bought brand new set of BFG KM2s with wheels originally arrived with JK. 

The 255/75R17 BFGoodrich Mud-Terrain T/A KM2 has a diameter of 32.05", bit smaller than my old 33x10.50R15. 

The OEM JK wheel has 6" backspace and 5x5 bolt pattern. Purchased 1" 5x4.5 to 5x5 spacer also. 

Siped center lugs, all of them. 

Due to backspacing, tires sit inside wheel well and decided to cut fender flares accordingly.

almost half width of fender flares are cut 

Ready to roll

 

After 8 years of rolling, my old 33 still have a decent amount of tread, but new set of tires always be good. 

 

 

 

 

EFS Extreme steering damper

Installed a steering damper made for JK, an Australian brand EFS  Extreme. Made a custom clamp for mounting draglink end.

of course sticker goes on window :D

AW4 tag

 NP242J; 53007856

Dana 30 outer axle tube seal

 ordered a pair from ebay and they arrived, will install soon

Front Axle Tube Seal Kit For Jeep Wrangler JK TJ XJ ZJ MJ Dana 30 & 44 MG21103,

arrived in just a cardboard box, no manufacturer, part number etc

Windshield washer

Sometimes front windshield washer motor is not working and wiggling the wires helps. Checked all wires carefully, they are all normal. Suspecting module itself and decided to open and check. Drilled out 4 rivets and opened it. 

Yeah, reason was there, solder of leftmost contact is cracked, the pin can move freely up and down.

re-soldered all contacts and good to go.

Works like a charm ;)

This GM one is similar, plus it has a heatsink. Friend suggested it.

Part number is 15598496, Wiper motor module

 

EFS leaf spring and rear end bushings

Australian made EFS leaf springs (EFS Part# JEEP-02E), rear end bushings (EFS Part# UK761) 2 of VMWL-424 LED work lights arrived through bro.

As in the web page, this pack is for constant 150kg load, 63.5mm wide, 7 leaves,

 

 

 

Bushings are blue, manufacturer said they are made from high quality 80D rated elastomers

 

4" SQUARE 24W LED WORK LIGHT

 

 

Will install them later, when weather allows. Then will make suitable leaf spring shackle depending on height she sits after installation.

Thanks Bro.